Type 4 , Webcam and any! Performance parts

Started by IDA, November 21, 2017, 04:01:10 AM

« previous - next »

IDA

*****
Buggy Baron
Posts: 513
Mk2 Rat and LDV
Location: CHICHESTER
Type 4 Performance parts for a 2.0L will be turbo,
Webcam 86a or b cam or a full kit
Solid Rocker Shaft
swivel foot adjusters
Gasket kit
and any odd bits that I may need,,
Do not be offended by my spelling mistakes! Why asking tech? questions" As so far I have not asked Any,, Everyone fort it was in possible apart from the One who invented it..

farmer rob

****
Buggy Meister
Posts: 1,793
SWB Rat
Location: northants
Hi IDA, I've been building an engine for Mark (Zip Buggy) He wanted to go oval ports on his but he has got a set of square port heads with the larger 1800 size valves, these might seal better on the exhausts for a turbo. He has also got some 95mm B+P's in reasonable condition and I have a some new 94mm B+P's. One B+P was bought separate, so might need balancing with the other 3! but you could have them for £190.

Rob

Zip Buggy

***
Buggy Meister
Posts: 1,447
FF Buggy LWB
Location: Bourne, Lincs
I've sold the pistons and barrels but the heads are still available - £300 the pair delivered.
Who needs prozac when you can drive a buggy?

IDA

*****
Buggy Baron
Posts: 513
Mk2 Rat and LDV
Location: CHICHESTER
Thanks, guys, My turbo manifold is oval port and I got a lots of stock engine bits like 200mm flywheel 1800 heads As over the years I have pick up like 4! type4 engines I'm only fitting one as I'm building a driving buggy not show :o and it will be Auto so type4 will do the job!,,,
Do not be offended by my spelling mistakes! Why asking tech? questions" As so far I have not asked Any,, Everyone fort it was in possible apart from the One who invented it..

IDA

*****
Buggy Baron
Posts: 513
Mk2 Rat and LDV
Location: CHICHESTER
Quote from: farmer rob on November 22, 2017, 08:44:42 AM
Hi IDA, I've been building an engine for Mark (Zip Buggy) He wanted to go oval ports on his but he has got a set of square port heads with the larger 1800 size valves, these might seal better on the exhausts for a turbo. He has also got some 95mm B+P's in reasonable condition and I have a some new 94mm B+P's. One B+P was bought separate, so might need balancing with the other 3! but you could have them for £190.

Rob

Have you still got the 94mm B+P's!!
Do not be offended by my spelling mistakes! Why asking tech? questions" As so far I have not asked Any,, Everyone fort it was in possible apart from the One who invented it..

farmer rob

****
Buggy Meister
Posts: 1,793
SWB Rat
Location: northants
Hi IDA, I had a hunt round for my B+P's today. To be honest, I do not think they are any good as a full set because the one piston is a different make and is 27grams heavier than the other 3 so that would be a lot of metal to remove to match it up. Sorry!!

Rob

moogster

*
Jr. Member
Posts: 18
VOLKSROD MK IV LWB
Location: Shepshed, Leicestershire
I have a set of porsche 2ltr 914 heads 3 studs on the intake fitment. 41mm intake 34mm exhaust valves Had them for years doubt ill ever use them.  one has a couple of small bits missing off the cooling fins. Was gonna get these all sorted at S.E.P in kegworth £500 if any interest.

IDA

*****
Buggy Baron
Posts: 513
Mk2 Rat and LDV
Location: CHICHESTER
Thank's I'm ok on heads

,,,I need some 2L barrels
and cam bits and porsche Fan
Do not be offended by my spelling mistakes! Why asking tech? questions" As so far I have not asked Any,, Everyone fort it was in possible apart from the One who invented it..

SMF spam blocked by CleanTalk