Welcome, Guest. Please login or register.
April 21, 2021, 10:41:54 AM

Show Posts - Buggybaggy

Welcome to Beach Buggy .Info - The UK's Online Beach Buggy Community.

Show Posts

You can view here all posts made by this member. Note that you can only see posts made in areas to which you currently have access.


Topics - Buggybaggy

Pages: [1] 2 3 ... 7
1
Beach Buggy Engine and Exhaust Help / Head re-torque
« on: April 02, 2021, 07:27:41 PM »
Hi guys, my cylinder heads need a re-torque and I'm thinking that because I have twin carbs this should be do-able without dropping the engine.
Carbs/manifolds off, cylinder shrouds off, rocker shafts off. Re-torque, all back together, valve clearences set, jobs a goodun.
10 says I'm forgetting something obvious.....as per normal.
Thoughts?
Thanks.

2
Events, Cruises and Gatherings / Stanford Hall 2021 postponed
« on: January 30, 2021, 11:20:48 AM »
No great surprise as it's a fairly early meet.


3
Beach Buggy Rolling Chassis Help / Axle gaiters, again!
« on: October 03, 2020, 11:21:37 AM »
I replaced tge axle gaiters a while ago, but I'm not at all happy with the fit of the circular clips at each end. Icm going to remove them and use the previouly fitted jubilee style ones.
So, what's the chances of being able to do this without draining the box?
I'm guessing perfectly doable if I want my garage floor covered in box oil, otherwise don't try to cut corners.  Am I correct?

4
Beach Buggy Engine and Exhaust Help / Enough bowden tube bend?
« on: September 27, 2020, 03:16:38 PM »



Getting a bit of judder occasionally setting off in first. Box front mount looks OK and is tight as. Thought I'd got enough bowden bend, but maybe not.
Thoughts?
Thanks

5
Beach Buggy Engine and Exhaust Help / Cracked starter solenoid
« on: September 09, 2020, 05:10:47 PM »
I cracked the plastic end cap of my starter solenoid.
Options?

Ta.


6
Parts Wanted / Exhaust to clear twin carbs.
« on: September 03, 2020, 09:12:16 PM »
Got a new motor with twin carbs but neither my cannon nor merged exhsussts will clear the carbs sufficiently. I plan to get a new exhaust made, but need something to put me on for a couple if months.
Anyone got anything suitable and cheap? (don't want to spend a small fortune for just a few weeks use.)
Thanks.

7
Beach Buggy Electrical Help / Fuel pump wiring.
« on: September 03, 2020, 06:18:17 PM »
Wirung in an electric fuel pump, which seems straight forward enough, one wire yo ground and a feed which I'm planning to do from the same feed as the coil.
Any issues so far?

I'm also wondering about putting a switch in to act line of security, working on the buggy not getting far if the buggy were to be hot wired but the pump not be switched on.
I'd wire the switch to a relay, and have the relay provide the power to the pump.
Any issues there?

Any thoughts pro/con this idea would be welcome.  ;-)up
Thanks

8
Parts Wanted / Wanted - fuel pump blanking plate.
« on: August 16, 2020, 01:14:30 PM »
Anyone got one sat doing nothing.
All the badic ones seem to be 'out of stock' and I don't feel minded ti spend more on a fancy dan one which costs more than an actual pimp.
Ta.

9
Beach Buggy Engine and Exhaust Help / Setting up twin carbs / exhaust.
« on: August 16, 2020, 08:12:13 AM »
Would using twin cannon exhaust make setting up twin carbs easier than using a 4 into 1 exhaust?

10
Beach Buggy Engine and Exhaust Help / Which electric fuel pumpm
« on: August 09, 2020, 09:41:28 PM »
Changing to Weber 34 ICTs with a bell crank throttle.
Looks like the bell crank will foul my mechanicsl fuel pump so considering an electric one. But which?
Any recomendations?
What about pressure regulator? Built in or seperate from pump, and fixed pressure or variable?
 :-\
Thanks.

11
Beach Buggy Engine and Exhaust Help / Fan bolt torque
« on: August 09, 2020, 12:42:10 PM »
Putting the alternator and fan back together.
The book says 43lb foot for the fam bolt. But my socket is a 3/4 inch drive snd my torque wrench 1/2 inch.
So how tight is 43lb foot?
Must have done it OK last time when I put the new fan on.

12
So guys, I've got a new backing plate for my alternator which has a hole in it. My old one does not hsve yhe hole. Have I ordered the wrong part?
The hole I'm referring to is the one at 12 o'clock.
Thanks



13
Parts Wanted / Spacers for Weber 34ict
« on: June 28, 2020, 01:44:35 PM »
Hi, I'ma looking for a pair of 10mm (or there abouts) spacers to go between Weber 34 ict carbs and inlet manifolds.
Anyone got any knoocking about?
Cheers.

14
Parts Wanted / Volksrod engine lid.
« on: June 11, 2020, 09:33:56 PM »
Got a bit of an idea knocking around in my head, but I need a Volksrod engine lid if snyone has one knocking sbout.
Condition is not overly important.
Thanks.

15
Beach Buggy General Help / Starter bush replacenent
« on: March 14, 2020, 03:25:11 PM »
How do I fit a new starter motor bush?
I've drifted the old one out from the flywheel end. But how best to get the new one in without manglung it?
Also, can it be put in fton the flywheel end, or must it be put in from the starter end?
Thanks.

Pages: [1] 2 3 ... 7